67 lines
1.9 KiB
C
67 lines
1.9 KiB
C
|
/**
|
||
|
|
******************************************************************************
|
||
|
|
* @file gpio.c
|
||
|
|
* @brief This file provides code for the configuration
|
||
|
|
* of all used GPIO pins.
|
||
|
|
******************************************************************************
|
||
|
|
* @attention
|
||
|
|
*
|
||
|
|
* <h2><center>© Copyright (c) 2023 STMicroelectronics.
|
||
|
|
* All rights reserved.</center></h2>
|
||
|
|
*
|
||
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
||
|
|
* the "License"; You may not use this file except in compliance with the
|
||
|
|
* License. You may obtain a copy of the License at:
|
||
|
|
* opensource.org/licenses/BSD-3-Clause
|
||
|
|
*
|
||
|
|
******************************************************************************
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* Includes ------------------------------------------------------------------*/
|
||
|
|
#include "gpio.h"
|
||
|
|
|
||
|
|
/* USER CODE BEGIN 0 */
|
||
|
|
|
||
|
|
/* USER CODE END 0 */
|
||
|
|
|
||
|
|
/*----------------------------------------------------------------------------*/
|
||
|
|
/* Configure GPIO */
|
||
|
|
/*----------------------------------------------------------------------------*/
|
||
|
|
/* USER CODE BEGIN 1 */
|
||
|
|
|
||
|
|
/* USER CODE END 1 */
|
||
|
|
|
||
|
|
/** Configure pins as
|
||
|
|
* Analog
|
||
|
|
* Input
|
||
|
|
* Output
|
||
|
|
* EVENT_OUT
|
||
|
|
* EXTI
|
||
|
|
*/
|
||
|
|
void MX_GPIO_Init(void)
|
||
|
|
{
|
||
|
|
|
||
|
|
GPIO_InitTypeDef GPIO_InitStruct = {0};
|
||
|
|
|
||
|
|
/* GPIO Ports Clock Enable */
|
||
|
|
__HAL_RCC_GPIOH_CLK_ENABLE();
|
||
|
|
__HAL_RCC_GPIOG_CLK_ENABLE();
|
||
|
|
|
||
|
|
/*Configure GPIO pin Output Level */
|
||
|
|
HAL_GPIO_WritePin(beep_GPIO_Port, beep_Pin, GPIO_PIN_SET);
|
||
|
|
|
||
|
|
/*Configure GPIO pin : PtPin */
|
||
|
|
GPIO_InitStruct.Pin = beep_Pin;
|
||
|
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
||
|
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
||
|
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
||
|
|
HAL_GPIO_Init(beep_GPIO_Port, &GPIO_InitStruct);
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
/* USER CODE BEGIN 2 */
|
||
|
|
|
||
|
|
/* USER CODE END 2 */
|
||
|
|
|
||
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|